Spray foam insulation removal in Bridgwater, Somerset, is what we do every week: cutting out failed open cell and closed cell foam from lofts, rafters and cavity walls, then extracting the debris with industrial vacuum units so your roof timber can dry and breathe again. If a surveyor flagged spray foam, or your lender has stalled your mortgage, we can get the roof back to a mortgageable state. We cover Eastover, Hamp, Wembdon and the wider TA6 area.
Spray foam insulation removal in Bridgwater, Somerset, is the controlled cutting, scraping and vacuuming of polyurethane foam that has been sprayed onto roof timbers, loft decks or cavity walls. We work from the ridge down, using an oscillating multi-tool and reciprocating saw to slice foam away from rafters without gouging the timber, then a boroscope inspection camera to check what is hidden behind the membrane. Every surface is checked with a moisture meter and thermal imaging camera before we sign the job off.
Most Bridgwater call-outs start the same way: a mortgage lender refuses to lend, or a surveyor flags spray foam insulation on a house near Taunton Road or Bath Road. Closed cell spray foam traps moisture against roof timber, and in a Somerset climate that means rot, condensation and damp within a few seasons. We also handle spray foam extraction Bridgwater homeowners need after a botched DIY loft job, and we can usually give you a spray foam insulation removal cost Bridgwater figure the same day you call.
Every removal job is quoted as a complete package, so you know what is covered before we start. The list below is standard on domestic lofts and roofs. Cavity wall extraction, timber replacement and replacement insulation are priced separately after the survey.
We inspect the foam, photograph it, and take moisture readings on the roof timber with a moisture meter and thermal imaging camera. You get a written scope and a fixed price the same day, usually within two hours of the visit.
Technicians in PPE disposable coveralls and respirator filters cut the foam away with an oscillating multi-tool and reciprocating saw. An industrial vacuum extraction unit and air scrubber run throughout, so dust never reaches your living space.
All foam debris is vacuumed into sealed bags and removed from site. Nothing is left in the loft, and we do not tip foam into your wheelie bin. Waste goes to a licensed disposal route wherever the material allows.
Once the foam is out we check every rafter for rot, confirm the breathable membrane is intact and clear any blocked eaves ventilation. Any timber needing replacement is photographed and quoted before we proceed.
You receive before-and-after photographs, moisture readings and a written method statement. This is the pack lenders and surveyors ask for on spray foam insulation removal for mortgage Bridgwater cases, and it usually settles the query first time.
We vacuum the space again, remove all sheeting and walk you through the finished loft. You see exactly what was done, where the timber was checked and what we recommend for replacement insulation going forward.
We inspect the loft, roof space or cavity, photograph the foam, and take moisture readings on the rafters. You get a fixed price the same day, usually within two hours of the visit. If the foam is only on the loft floor rather than the roof deck, the job is smaller and the price reflects that.
Before any cutting starts we lay protective sheeting, seal the loft hatch and set up the industrial vacuum extraction unit with a negative air machine. This keeps foam dust out of your bedrooms and kitchen. Setup takes around 45 minutes on a typical Bridgwater semi.
Technicians in PPE disposable coveralls and respirator filters cut the foam away from roof timber with an oscillating multi-tool and reciprocating saw, working section by section. Debris goes straight into the vacuum, not onto the floor. A standard three-bedroom loft takes one to two working days.
With the foam gone we check every rafter with a moisture meter and boroscope inspection camera, looking for rot, insect damage and blocked eaves. Anything flagged is photographed and priced separately before we touch it. This is the stage that decides whether the roof is mortgageable.
We vacuum the whole space again, wipe down surfaces, remove sheeting and walk you through the finished loft. You get before-and-after photos and the moisture readings in writing. Most customers are back to a normal, usable loft the same evening.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Cuts closed cell foam away from rafters without gouging the timber. The fine blade control is what keeps your roof structure intact on tight Bridgwater lofts.
Used on thicker foam sections and where foam has bonded across multiple rafters. We cut in controlled passes so the blade never bites into the roof deck.
Pulls foam debris straight out of the loft into sealed containment. This is the machine that keeps dust out of your bedrooms and kitchen during the job.
Run together to keep the loft under negative pressure, so any airborne particles are filtered rather than drifting into the rest of the house.
Lets us see behind membranes, into eaves gaps and inside cavities before we commit to a removal method. Essential on older Bridgwater properties with hidden roof details.
Measure timber moisture and spot cold bridging or hidden damp. These readings form the before-and-after evidence your lender or surveyor will ask for.
Lifts thin foam films and residue from delicate surfaces such as brickwork and finished rafters without abrasion, then the vacuum takes the waste away.
A three-bedroom Victorian terrace in Eastover had closed cell foam sprayed across the entire roof deck. The buyer's surveyor flagged it, the lender froze the mortgage, and the sale had already been delayed by five weeks.
We removed 100% of the foam in two working days, cleared the blocked eaves ventilation and confirmed all rafters read dry on the moisture meter. The documentation pack went to the solicitor on day three, and the lender released the offer nine days later.
Foam had been in the loft of a Wembdon semi for around six years. The upstairs bedrooms smelled musty every winter and two rafters were soft to the touch. The homeowner had already redecorated twice with no lasting effect.
We cut the foam out over two days, replaced one rafter and cleared the ventilation path. Moisture readings dropped from 24% to 17% within three weeks, and the musty smell cleared within 24 hours of us finishing. No further decorating has been needed.
A rented property in Sydenham had damp patches on the front room wall and a cold spot that no amount of heating fixed. Foam had been injected into the cavity years earlier and was bridging the gap between the two leaves of brickwork.
We extracted the foam through drilled access points over a single day, confirmed the cavity was clear and made good the brickwork. The damp patches dried out over the following month and the property passed its next landlord inspection with no foam-related notes.
Spray foam causes four problems we see again and again in Bridgwater lofts. Each one has a practical fix, and none of them get better by waiting.
Ask a pro →We remove the foam, restore roof ventilation and supply a documentation pack with photographs and moisture readings. Most Bridgwater lenders accept this evidence and release the mortgage offer within a fortnight of the work finishing.
We cut the foam back to bare timber, check every rafter with a moisture meter and boroscope inspection camera, and flag anything soft. Drying starts immediately once airflow is restored, and we quote any timber replacement before we touch it.
We clear the ventilation path from eaves to ridge, check the vapour barrier and confirm air is moving again. Most customers see condensation stop within a week and the loft smell clear within 24 hours of us finishing.
We carry out an insulation assessment using a thermal imaging camera and moisture meter, then quote the removal. If you proceed, the same documentation pack goes to your solicitor and lender, which is what most Bridgwater conveyancers ask for.
Typical 2026 pricing in Bridgwater runs from around 1,800 to 4,500 pounds for a standard three-bedroom loft, depending on foam thickness, access and how much timber needs treating. Cavity wall foam removal is priced separately. We give you a fixed figure after the survey, so there is no hourly rate and no surprise on the final invoice.
Removal is the cutting and scraping of foam off the roof timber. Extraction is what happens to the waste: an industrial vacuum extraction unit pulls the debris out of the loft and into sealed bags, so nothing settles in your house. We do both in the same visit, which is why spray foam removal and extraction Bridgwater jobs are quoted as one price.
Yes. We remove open cell and closed cell spray foam from roof decks, rafters, loft floors, cavity walls and commercial ceilings. On a typical Bridgwater semi we clear 100% of accessible foam in one to two days. Foam behind plasterboard or inside a sealed cavity is assessed first with a boroscope inspection camera, and we tell you exactly what can and cannot be reached.
A three-bedroom loft takes one to two working days. Larger roofs, thick closed cell foam or heavy timber rot can stretch to three or four days. Cavity wall extraction is usually a single day. We confirm the timeframe at survey and keep to it, because most customers are working around a mortgage deadline or a house sale.
Spray Foam Removal near meIf you are searching for spray foam removal near me in Bridgwater, this is the core service: cutting foam off roof timber, vacuuming the waste and restoring ventilation. We cover the TA6 and TA7 postcodes and the surrounding Somerset villages.Explore →
Same day Spray Foam RemovalWhere the diary allows, we can survey and start the same day, which suits Bridgwater homeowners working to a tight mortgage or house-sale deadline. Call before midday and we will tell you honestly whether a same-day start is possible.Explore →
24/7 Spray Foam RemovalEmergency call-outs for water ingress through failed foam, or foam that has started to break down and drop into a loft. We answer the phone around the clock on 0127 827 6038 and can usually attend within 24 hours across Bridgwater.Explore →
Residential Spray Foam RemovalHouses, bungalows and flats across Bridgwater, from Victorian terraces near the town centre to modern builds in Stockmoor Village. We work dust-controlled, protect your carpets and leave the loft clean enough to use the same evening.Explore →
Commercial Spray Foam RemovalWarehouse ceilings, agricultural buildings and commercial roofs around Dunball and Puriton. Larger jobs are phased so your operation keeps running, and we work to PAS 2035 principles when reinstating insulation to the same thermal standard.Explore →
Loft Spray Foam RemovalThe most common job we do in Bridgwater. Foam sprayed between rafters blocks eaves ventilation and traps condensation, so we cut it back, clear the airflow path and check the vapour barrier before signing off.Explore →
Roof Spray Foam RemovalFoam applied directly to the underside of the roof deck is the hardest to remove and the biggest cause of mortgage refusal. We work from the ridge down, section by section, and photograph every rafter for your lender's surveyor.Explore →
Attic Spray Foam RemovalAttic spaces in older Bridgwater properties often have foam over both the rafters and the joists. We remove both, then confirm the breathable membrane and roof timber are sound before recommending any replacement insulation.Explore →If a surveyor has flagged your foam, or your loft is damp and smells, call us on 0127 827 6038. We are CHAS accredited, insured, and we give fixed written prices after a same-day survey. Most Bridgwater jobs are booked within 48 hours.
Get a fixed quote 0127 827 6038 →Call 0127 827 6038 or email us and a technician will get back to you the same working day. We answer the phone from 8am to 6pm Monday to Friday, and our emergency line is staffed 24/7 for urgent foam problems. Free surveys across Bridgwater and the surrounding villages, usually booked within two working days.